- Filaments
- PLA+
- PLA Transparent
- ePLA
- ePLA-ST
- ePLA-LW
- PLA Luminous-Rainbow
- eStars-PLA
- Re-filament
- eSUN 4D Filament e4D-1
- Respool
- PETG
- ABS
- ABS+
- ABS Odorless
- eSilk-PLA
- eTwinkling
- eMarble
- WOOD
- eTPU-95A
- eLastic(TPE-85A)
- eFlex(TPU-87A)
- PVA
- ePVA+
- eASA
- ePA
- ePC
- ePA12
- ePA-CF
- ePA12-CF
- ePAHT-CF
- ePEEK Pro
- eABS Max
- HIPS
- eCleaning
- eMate-PCL
- DuPont™ Filament
- Resins
- Accessories
- Printers
- 3D Pens
ePAHT-CF
ePAHT-CF（Nylon Carbon Fiber）
Product Description :
ePAHT-CF (Nylon Carbon Fiber) is a material jointly developed by eSUN and LUVOCOM. Its print has matte and delicate finish. The filament has added high-rigidity carbon fiber based on the properties of nylon, with high mechanical strength, impact resistance, high rigidity, and heat resistance up to 150℃.
ePAHT-CF (nylon carbon fiber) is a material jointly developed by eSUN and LUVOCOM.
Compared with PA66, the size and electrical properties of ePAHT-CF are less affected by humidity and temperature. The strength of ePAHT-CF is higher than other eSUN nylon series products. The surface of the printed items is matte and fine. On the basis of the performance of PA6, 15% high-rigidity carbon fiber is added, high-strength, high-rigidity, impact resistance, self-lubricating and abrasion resistance, excellent chemical resistance, high temperature resistance, the continuous use temperature of the parts can reach 150°C, and the short-term use temperature can reach 180°C. It can be detected by metal detector (≥ 2 mm³). The strip electrode insulation resistance and surface resistance are less than 102Ω. It can be used as a conductive and antistatic material. Compared with pure nylon, the shrinkage rate and water absorption rate are greatly reduced. The printed model has high dimensional stability, good mechanical performance, good interlayer bonding, excellent printability, low distortion, no warping, and no chamber or bed heat is required.
Product advantages:
- High strength, high rigidity, the strength is much higher than other eSUN nylon series products
- Excellent chemical resistance
- High temperature resistance
- High dimensional stability
- Excellent surface effect
- Excellent printability, good interlayer adhesion, no warping
- Conductive and antistatic
Physical performance indicators:
|
Filament |
ePAHT-CF |
|
Melt Index |
19.68(270℃/2.16kg) |
|
density |
1.4g/cm3 |
|
Impact strength |
12.74 |
|
Tensile Strength |
173.37Mpa |
|
Elongation at break |
8.93% |
|
Bending strength |
171.64Mpa |
|
Flexural modulus |
5612.41Mpa |
|
Heat distortion temperature |
190℃ |
|
Continuous use temperature (UL 746B) |
150℃ |
|
Short-term use temperature |
180℃ |
|
Bar electrode insulation resistance |
≤10²Ω |
|
Surface resistance |
<10²Ω |
Physical performance indicators：
|
Filament |
ePA-CF |
ePAHT-CF |
ePA12-CF |
ePAHT-GK |
|
Impact strength |
18.67 KJ/M2 |
12.74 KJ/M2 |
11.33 KJ/M2 |
8.52 KJ/M2 |
|
Tensile Strength |
140Mpa |
173.37 Mpa |
108.18 Mpa |
80.75 Mpa |
|
Elongation at break |
10.61% |
8.93% |
9.02% |
10.35% |
|
Bending strength |
140Mpa |
171.64Mpa |
116.58Mpa |
88.54Mpa |
|
Flexural modulus |
4363Mpa |
5612.41Mpa |
3335 Mpa |
1743Mpa |
|
Heat distortion temperature |
155℃ |
190℃ |
90℃ |
75.4℃ |
Print parameters：
|
Filament |
ePAHT-CF |
|
Recommended print temperature |
260-300℃ |
|
Bed |
45-60℃(Masking paper, PVP solid glue, glass board, carbon fiber board, PEI) |
|
Fan |
0% |
|
Print speed |
40-100mm/s |
Print performance comparison
|
|
ePA-CF |
ePAHT-CF |
结论 Conclusion |
|
Surface finish |
No obvious layer pattern Matte surface |
No obvious layer pattern Matte surface |
ePAHT-CF=ePA-CF |
|
Hole-column fit model (The smaller the value, the better) |
0.3mm |
0.3mm |
ePAHT-CF=ePA-CF |
|
Suspension model (The larger the value, the better) |
≤70° |
≤70° |
ePAHT-CF=ePA-CF |
|
Suspended bridge (The larger the value, the better) |
50mm |
50mm |
ePAHT-CF=ePA-CF |
Note: Print test conditions: nozzle 280℃; bed 80℃; speed 40mm/s
Precautions:
ePAHT-CF is easy to absorb water, please dry before printing (70℃/12H). It is recommended to use with eSUN eBOX when printing. ePAHT-CF is very easy to grind nozzles and extruder gears. It is recommended to use hardened steel nozzles or ruby nozzles. Hardened steel extruder gears can be selected if possible. If the throat printing time is long, it needs to be replaced. It is recommended to use with eBOX and ruby nozzle together.
